Urocare Uro-Con Texas Style Male External Catheter With Urofoam And Uro-Prep

Why choose UroCon Texas-Style Male External Catheter System?

• Each Uro-Con catheter has a thin, latex sheath similar to a condom which is rolled over the head and shaft of the penis
• It is attached to a 4"(10cm) or 2"(5cm) white-silicone tube where urine is drained from into a bag or other collection device by an plastic catheter insert.
• Using a Condom type sheath makes these catheters fully collapsible to prevent pooled urine a major cause of skin irritation and break-down
• Back side of the pouch contains detailed, illustrated, application instructions
• Packaged individually in a window pouch allowing for quick, easy product identification without opening the pouch
• Uro-Con male external catheters can also be packaged with protective skin barrier wipes

Uro-Cath Male Catheter User Manual

What to buy with UroCare Uro-Con Texas-Style Male External Catheter

• Bard Latex Leg Bag Extension Tubing With Connector
• Urocare Tubing Connectors
• ConvaTec Aloe Vesta Perineal Or Skin Cleanser

Also available (separately):

• Urocare Urofoam Adhesive Foam Strips (Code 5100)
• Urocare Uro-Con Texas Style Male External Catheter
• Urocare Uro-Con Texas Style Male External Catheter With Urofoam

How to use UroCon Texas-Style Male External Catheter System?

Choose the method which best suits your requirements. Follow the instructions carefully. In most cases, good results are obtained with an erection to prevent possible problems with circulation.

• Method A: Use Urofoam -1 Single-Sided Adhesive Foam Strip.
  1. Trim pubic hair if necessary. Thoroughly clean penis and let dry. Then place catheter over head of penis and unroll catheter sheath down entire penis shaft.
  2. Remove paper liner from Urofoam -1 adhesive foam strip.
  3. Starting just behind the head of the penis, with the adhesive side down, spiral-wrap the Urofoam -1 adhesive strip snugly around catheter.
     Caution: To avoid circulation restriction, do not wrap the adhesive strip too tight.
  4. Connect to drainage system and check periodically.


• Method B: Use Urofoam -2 Double-Sided Adhesive Foam Strip
  1. Trim pubic hair if necessary. Thoroughly clean penis and let dry.
  2. Remove shorter paper liner from Urofoam -2 adhesive foam strip.
  3. Starting just behind the head of the penis, with the adhesive side down, spiral-wrap the Urofoam -2 approximately a ¾ wrap. Then remove the second paper liner as needed and continue around the penis as shown in.
     Caution: To avoid circulation restriction, do not wrap the adhesive strip too tight.
  4. Then place catheter over head of penis and unroll catheter sheath down entire penis shaft. Press sheath firmly onto foam strip to remove any air pockets or creases in sheath to ensure a leak-proof seal.
  5. Connect to drainage system and check periodically.


• Method C: Use Uro-Bond Brush-on Silicone Adhesive only
  1. Trim pubic hair if necessary. Thoroughly clean penis and let dry. Then place catheter over head of penis and hold in place with finger tips.
  2. To apply Uro-Bond silicone adhesive, paint penis shaft evenly with silicone adhesive—be certain to encircle entire penis shaft. Wait 1 minute to get tacky.
  3. Unroll catheter sheath smoothly, making good contact with silicone adhesive. Press sheath firmly onto skin to remove any air pockets or creases in sheath to ensure a leak-proof seal.


• Method D: Use Uro-Bond and Constay Tape or Urofoam -1
  1. Trim pubic hair if necessary. Thoroughly clean penis and let dry. Then place catheter over head of penis and hold in place with finger tips.
  2. To apply Uro-Bond silicone adhesive, paint penis shaft evenly with silicone adhesive—be certain to encircle entire penis shaft. Wait 1 minute to get tacky.
  3. Unroll catheter sheath smoothly, making good contact with silicone adhesive. Press sheath firmly onto skin to remove any air pockets or creases in sheath to ensure a leak-proof seal.
  4. Remove bead (rubber ring) if necessary.
  5. Cut enough Constay tape to encircle penis at least once or use a Urofoam -1 strip to encircle penis. Place the Constay or Urofoam -1 strip half on and half off the catheter sheath.
  6. Connect to drainage system and check periodically.


• Method E: Use Uro-Bond and Constay Tape or Urofoam -1
  1. Trim pubic hair if necessary. Thoroughly clean penis and let dry. Then place catheter over head of penis and hold in place with finger tips.
  2. To apply Uro-Bond silicone adhesive, paint penis shaft evenly with silicone adhesive—be certain to encircle entire penis shaft. Wait 1 minute to get tacky.
  3. Unroll catheter sheath smoothly, making good contact with silicone adhesive. Press sheath firmly onto skin to remove any air pockets or creases in sheath to ensure a leak-proof seal.
  4. Reverse direction and unroll catheter sheath back up the penile shaft about 1" (2.5cm) as
  5. Cut enough Constay tape to encircle penis at least once or use a Urofoam -1 strip. Place the Constay or Urofoam -1 strip half on/half off the catheter sheath.
  6. Encircle at least once—press the Constay tape or Urofoam -1 strip firmly against the skin and catheter sheath.
  7. Reverse direction again and unroll the remaining catheter sheath back over the Constay tape or Urofoam -1 strip.
     Caution: To avoid circulation restriction, do not wrap the adhesive strip too tight.
  8. Connect to drainage system and check periodically.