Rolyan Forearm-Based Thumb Spica Splint

Features of Rolyan Forearm-Based Thumb Spica Splint

• Made with the most conformable of all Rolyan" splinting materials
• Natural drape provides an intimate tit for increased patient comfort and minimal handling Good contour leads to reduced pressure areas and reduced splint migration
• Excellent rigidity and strength when set
• Edges finish well
• Coated, allowing temporary bonds
• Includes all necessary strapping and a self-adhesive D-ring strap to securely hold the thumb
• Pre-formed from 1/16"" Polyform material with 1/8"" Plastazote padding
• For size, measure the width of the 2nd to 5th MCP
• Latex free
• Rolyan Forearm-Based Thumb Spica Splint User Manual

When to use Rolyan Forearm Thumb Spica Splint?

• To support the CMC and immobilize the MCP joints of the thumb
• May be used for arthritis, skier’s thumb, and gamekeeper’s thumb
• Rolyan Forearm-Based Thumb Spica Splint-
  • For additional immobilization of the wrist
  • May also be used for deQuervain’s syndrome Ideal for people with pain or irritation of the joints. requiring gentle handling

What to buy with Forearm Based Thumb Spica Splint?

• Rolyan Digi-Block Hand Exerciser
• Biofreeze Professional Pain Relieving Roll-On

How to apply Thumb Spica Splint?

Making modifications:

1. Before permanently attaching liner to splint, apply the splint (with liner in place) to check for fit. To trim or modify the splint, remove it and spot-heat it with a heat gun or in a heat pan of water at a temperature of 150° to 160° F (65°–70°C) for 30 seconds or until pliable. Heating the entire splint may cause it to lose its preformed shape. Polyform Light has a high degree of drape—for better results when modifying the material, shape it with stroking movements.
2. Remove the backing from the adhesive strips on the back of the liner and apply liner to splint.

Apply straps - Forearm-Based Splint:

3. With the splint on the patient, attach the two 11/2”-wide (3.8cm) foam straps around the forearm.

Both splints:

4. With the splint on the patient, position the 1”-wide (2.5cm) strap across the dorsum of the hand and attach the self-adhesive loop on the strap to the ulnar side of the splint. Attach the self-adhesive hook coin to the radial side of the splint and fasten the strap.
5. Position the D-ring strap around the thumb area so the strap pulls in the direction of the thumb overlap before passing through the D-ring. Attach the self-adhesive hook tab to the splint.
6. A properly applied Hand-Based Thumb Spica Splint a Forearm-Based Thumb Spica Splint

Care and Cleaning of Forearm Based Thumb Spica

• The splint will lose its shape in temperatures over 135°F (57°C). It should be kept away from sources of heat such as ovens, hot water, open flames, and sunny car windows.
• The splint may be cleaned with soap and lukewarm water. The straps may be washed with soap and water, but the adhesive portion should not be moistened. The splint and straps should be allowed to dry thoroughly before reapplication of the splint.

Contraindications:

• Not in the presence of severe edema
• Not for the acute phase of most wrist or thumb fractures
• Not over open wounds and infected areas

Precautions:

• These splints are to be fitted initially by a healthcare professional who is familiar with the purpose for which they are prescribed. The healthcare professional is responsible for providing wearing instructions and precautions to other healthcare practitioners, care providers involved in the patient’s care, and the patient.
• If unusual swelling, skin discoloration or discomfort occurs, use should be discontinued and a healthcare professional consulted.
• Be careful that the splint is not so tight that circulation is impaired.
• After heating splinting material, always check its temperature before applying it to the patient.