Pride Jazzy 600 ES Power Chair

Features of Pride Jazzy 600 ES Power Chair

• OMNI-Casters (nylon, spherical-shaped casters) on front and rear to prevent wheel hang-ups
• Side-mounted, easily accessible freewheel levers
• Active-Trac ATX Suspension for enhanced performance over more varied terrain
• Easy front access to batteries
• Offers true all-around performance indoors and out
• Transitions curbs smoothly and is rated for climbing and aggressive performance, making it an excellent power chair choice
• Depth adjustable, black high-back seat
• Flip-up, removable, height and width adjustable armrest
• Universal, fixed, in-line joystick mount
• Flip-up height adjustable foot platform
• Black, flat-free, non-marking tires
• 6" lap belt
• Pride FDA Class II Medical Devices are designed to aid individuals with mobility impairments

Pride Jazzy 600 ES Power Chair Parts

1. Seatback
2. Armrest
3. Joystick
4. Controller
5. Seat Base
6. Front rigging (foot platform shown)
7. Caster Wheel
8. Spring Shock/Gas Damper Location
9. Drive Wheel
10. Manual Freewheel Lever
11. Caster wheel
12. Power base assembly
13. Armrest
14. Seat assembly

 

What to buy with Jazzy 600 Electric Wheelchair

• Graham-Field Single Release Folding Walkers - Standard Rubberized PVC Grip
• Guldmann Wide Plain Ramp
• Sammons Preston StandEasy Chair Lift

How to use Jazzy 600 ES Electric Wheelchairs?

To install the seat:

1. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar.
2. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
3. Flip the seat latch safety down.
4. Install the controller and route the harness to the back of the power base.
5. Plug the controller connector into the rear of the power base.
6. Secure the controller harness to the armrest receiver with wire ties.

To change the seat height:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Flip up the seat latch safety.
5. Squeeze the seat latch and release the seat from the front trapeze bar.
6. Slide the seat forward and remove it from the power base.
7. Remove the hardware that attaches the trapeze bars to the seat interface weldments.
8. Move the trapeze bars up or down to the desired height.
   Note: Change the seat dump by raising or lowering only one trapeze bar (front or rear).
9. Reinstall the hardware.
10. Reinstall the seat.
11. Reconnect the controller to the power base.

To change the seat position:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Remove both extrusions from the bottom of the seat.
6. Reposition the extrusions on a different set of mounting holes. You must move both extrusions to the same number of holes, either forward or backward. See figure 13.
7. Fasten the extrusions back onto the bottom of the seat.
8. Reinstall the seat.
9. Reconnect the controller to the power base.

To change the controller position:

1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power base.
3. Remove any wire ties securing the controller harness to the armrest.
4. Flip up the armrest so it is perpendicular to the floor.
5. Loosen the setscrew on the controller bracket
6. Slide the controller out of the armrest.
7. Loosen the setscrew in the other armrest.
8. Place the controller in the other armrest.
9. Tighten the setscrews in both armrests.
10. Route the controller harness to the back of the power base and plug in the controller.
11. Secure the controller harness to the armrest with wire ties.
    Note: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Positioning System, refer to the information provided in supplemental manuals provided with your seating system.

To charge the batteries using the off-board charger:

1. Position your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off, and the power chair is in drive mode.
3. Plug the off-board charger into the off-board charger/ programming socket on the controller.
4. Plug the off-board charger into the electrical outlet.
   Warning: The LED lights on the charger indicate different charger conditions at various times: charger power on, charging in progress, and charging complete. If the LED does not indicate that charging is complete within 24 hours, unplug the charger from the outlet and contact your authorized Pride Provider. Refer to the manual supplied with the charger for a complete explanation of these indicators.
5. When the batteries are fully charged, unplug the offboard charger from the electrical outlet and then from the controller.

Pride Mobility Jazzy 600 ES Power Wheelchair User Guides

• Jazzy 600 ES Power Wheelchair Owners Manual
• Jazzy 600 ES Power Chair Safety Guide
• Pride Jazzy 600ES Chair Specification Sheet