Pride Jazzy 1450 Heavy Duty Power Chair

Features of Pride Jazzy 1450 Heavy-Duty Powerchair

• Dual-layer powder coated frame for increased durability
• Durable construction to make it an exceptionally rugged power chair
• Unique design delivers high-performance operation indoors and out
• 600 lbs. weight capacity
• Maximum speed up to 4.5 mph
• High-performance, high-efficiency motor package
• Seat dimensions up to 32" by 28"
• Jazzy 1450 combines superb climbing capabilities with front anti-tips for transitioning over grade changes and handling various terrains easily

Pride Mobility Jazzy 1450 Power Chair Parts

1. Seatback
2. Armrest
3. Joystick
4. Controller
5. Seat base
6. Front rigging (foot platform shown)
7. Anti-tip wheel
8. Drive wheel
9. Power base assembly
10. Seat assembly

 

What to buy with Pride Jazzy 1450 Electric Wheelchairs

• Guldmann Wide Plain Ramp
• Graham-Field Single Release Folding Walkers - Standard Rubberized PVC Grip
• Sammons Preston StandEasy Chair Lift

How to use Pride Jazzy 1450 Heavy-Duty Power Wheelchair?

To install the seat:

1. Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 7.
2. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
3. Flip the seat latch safety down. WARNING! Make sure the seat latch safety is flipped down before using your power chair.
4. Install the controller and route the harness to the back of the power base. See figures 9 or 10. MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tiedown points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.
5. Plug the controller connector into the rear of the power base.
6. Secure the controller harness to the armrest receiver with wire ties.

To change the seat height:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base. See figure 3.
4. Flip up the seat latch safety. See figure 7.
5. Squeeze the seat latch and release the seat from the front trapeze bar.
6. Slide the seat forward and remove it from the power base.
7. Remove the hardware that attaches the trapeze bars to the seat interface weldments. See figure 11.
8. Move the trapeze bars up or down to the desired height.
9. Reinstall the hardware.
10. Reinstall the seat.
11. Reconnect the controller to the power base

To change the seat position:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Remove both extrusions from the bottom of the seat.
6. Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 12.
7. Fasten the extrusions back onto the bottom of the seat.
8. Reinstall the seat.
9. Reconnect the controller to the power base.

To change the controller position:

1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power base.
3. Remove any wire ties securing the controller harness to the armrest.
4. Flip up the armrest so it is perpendicular to the floor.
5. Loosen the setscrew on the controller bracket.
6. Slide the controller out of the armrest.
7. Loosen the setscrew in the other armrest.
8. Place the controller in the other armrest.
9. Tighten the setscrews in both armrests.
10. Route the controller harness to the back of the power base and plug in the controller.
11. Secure the controller harness to the armrest with wire ties.

To charge the batteries using the off-board charger:

1. Position your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the power chair is in drive mode.
3. Plug the off-board charger into the off-board charger/ programming socket on the controller. See figure 17.
4. Plug the off-board charger into the electrical outlet.