Ovation Medical Post Op Knee Brace

Ovation Medical Post Op Knee Brace Features

• Telescoping struts for length adjustment from 17"- 29"
• Simply rotate and release Flexion/Extension settings
• Unique safety lock to increase patient compliance
• 100% tool-free adjustments
• Drop lock button
• Quickly locks at 0, 10°, 20°, 30°, 45°, 60°, 75° & 90°
• Cool and Standard versions in Standard and XL sizes

How To Apply Ovation Medical Post Op Knee Brace?

Application Instructions For Post-Op Knee Standard Wrap

1. Open brace
2. Remove, unroll, and lay flat each of the two soft good foam wraps with the gray foam facing up. The wider wrap is for the thigh and the narrower wrap with the saw-tooth sidecut is for the calf. Position the leg over the foam wraps approximately in the center.
3. Wrap foam soft good around the leg snugly yet comfortably and secure with Velcro.
4. Position brace in a flat position. Set leg over brace centered approximately between both struts.
5. The leg should be positioned approximately, centered between struts with straps positioned to the rear of the leg. Verify hinge and buckle orientation.
6. Each side of the brace has 3 sliders that can be independently adjusted to accommodate different leg lengths. To adjust push slider button and move to the desired position. Ensure that the button “snaps” and locks into new position for secure placement and that both sides of the brace are set at the same positions.
7. Wrap brace around both sides of the leg. Struts should be positioned in the side view, with hinge slightly above the center of the knee. Note - Secure straps in the following sequence: 3,2,4,1 by inserting quick release buckle and tightening with a free end. Excess strap ends can be trimmed off.
8. ROM (Range of Motion) dials are unlocked by pushing button toward the center of the hinge. Push the button and rotate ROM dials to desired flexion/extension position and release button to lock. After adjustment make sure both left and right sides of the brace are set at the same positions.
9. The brace may be locked into one of 4 positions (0, 15, 30 and 45 degrees). Push Drop Lock lever DOWN to lock and UP to unlock. Always make sure both left and right locks are set at the same positions.
10. If desired the ROM Adjusters can be locked in position with included zip ties. To lock insert zip tie making sure it is behind button tab with a blue printed arrow. Wrap around ROM adjuster and secure snugly. Trim off excess after tightening

Application Instructions For Post-Op Knee Cool Wrap

1. Open brace
2. Position brace in a flat position. Set leg over brace centered approximately between both struts.
3. The leg should be positioned approximately, centered between struts with straps positioned to the rear of the leg. Verify hinge and buckle orientation.
4. Each side of the brace has 3 sliders that can be independently adjusted to accommodate different leg lengths. To adjust push slider button and move to the desired position. Ensure that the button “snaps” and locks into new position for secure placement and that both sides of the brace are set at the same positions.
5. Wrap brace around both sides of the leg. Struts should be positioned as the side view, with hinge slightly above the center of the knee.
   - Note - Secure straps in the following sequence: 3,2,4,1 by inserting quick release buckle and tightening with a free end. Excess strap ends can be trimmed off.
6. ROM (Range of Motion) dials are unlocked by pushing button toward the center of the hinge. Push the button and rotate ROM dials to desired flexion/extension position and release button to lock. After adjustment make sure both left and right sides of the brace are set at the same positions.
7. The brace may be locked into one of 4 positions (0, 15, 30 and 45 degrees). Push Drop Lock lever DOWN to lock and UP to unlock. Always make sure both left and right locks are set at the same positions.
8. If desired the ROM Adjusters can be locked in position with included zip ties. To lock insert zip tie, making sure it is behind button tab with a blue printed arrow. Wrap around ROM adjuster and secure snugly. Trim off excess after tightening.