Harmar Pinnacle SL300 Straight Stair Lift

Why choose Harmar SL300 Pinnacle Stair Lift?

• Pinnacle Stair Lift has safety obstruction sensors
• Swivel the seat for a safe exit
• Wide footrests for stability and extra comfort
• Low Maintenance & compact
• Folding rail design
• Pinnacle Chair Lift requires low maintenance
• Operable in a power outage
• Efficient motor that gives extended performance during power loss
• Helical worm gear and nylon polymer gear rack for a smooth ride and greater stability

 Features

• 20 Feet per Minute
• Safety Features include -obstruction sensors, 90-degree swivel interlock for safe ON/OFF, seat belt
• Seat - 19" W x 16" H x 18" D
• The optional folding rail deploys automatically and is a mechanical
• Lubrication-free, keeps you, your stairs, and even your pets free from a mess
• A low friction system provides a reduced cost of ownership
• No maintenance is required and lower energy bills
• Runs on batteries with efficient motor resulting in extended performance during power loss
• The over-sized worm gear offers greater stability
• A symmetrical design provides the industry’s most compact folded-width
• Pinnacle SL300 chassis folds up neatly, occupying a mere 11 Inches of width from your staircase wall, allowing others to pass by
• Rail mounts only 1 Inch from the wall and is only 3 Inch tall helping to stay out of sight
• Safety sensors in the footrest and optional in the chassis will stop the lift if it meets an obstruction
• SL300FR Folding Rail Features
  • Automatic deployment without the hassle of electronics
  • In continuous motion, the operator does not have to stop
  • Charging strips above and below the hinge for flexibility
  • Can order left or right-handed, but can be changed in the field
  • Includes chassis obstruction sensor
  • Increases minimum folded width to 13.5"
• SL300COS Folding Rail Features
  • Folds to 11.0"
  • Includes Chassis Obstruction Sensors

What to buy with Harmar SL300 Pinnacle Stair Lift

• Safepath EZ Edge Transition Rubber Threshold Ramp
• Roll-A-Ramp Seg Mount Brackets
• Ez-Access Suitcase Top Lip Extension

How to measure the dimensions before installing Harmar Pinnacle Stair Lift?

A to B - Inches from top landing to bottom floor

A to H - Inches from top landing to nearest obstruction

For Example: A Door

7" Overrun recommended if the top landing is clear (This is added to the A to B)

NOTE: If A to H is < 13", must order a tall bracket.

How to use Harmar SL300 Pinnacle Stair Lift?

1. To turn the inside stair lift on, press the red “ON/OFF” switch located on the top of the carriage to the “ON”
2.  To aid entry to the chair, the armrest on the entry side may be raised. When positioning yourself on the seat at the upper landing, ensure the seat is fully swiveled and locked in position for safety. The seat swivel is controlled by pressing the swivel release handle located at the side of the seat bottom. The footrest may be lowered to assist with entry and to keep your feet properly positioned during transport
3. Ensure that you are seated with the seat belt fastened and armrests in the down position before operating the Harmar SL300 lift. To operate the patient lift, continuously activate the hand control switch on the side in which you wish to travel
4. If you release the control switch, the lift will stop. Continue to activate the switch or button all the way to the landing. The lift will gently stop at the appropriate preset point
5. At the upper landing, swivel the seat away from the staircase until the seat is fully swiveled and locked, and remove your seat belt before rising. To safely exit the lift, remove the seat belt, support yourself by the armrests, and rise and step off the footrest. At the upper landing, ensure that the seat is fully swiveled and locked before rising. If you do not intend to use the lift again immediately, the seat and armrests may be folded up to minimize obstruction to people walking on the stairs
6. To operate the lift remotely, continuously press the appropriate up or down button on the call/send hand control unit. Hand control units are typically located at the upper and lower landings of the staircase

Folding Rail of Harmar Stair Lift

• Automatic
  • When ascending or depressing the stairs, the chassis will automatically activate the folding rail
• Between Uses
  • To keep your landing clear, use the remote call/send to move the Harmar SL300 stair lift up into the stairwell. The folding will automatically raise to keep the area clear

Maintenance of Harmar SL-300 Pinnacle

• Battery Charger
  • The stairlift should be kept fully charged at all times. When the lift stops within three (3’) feet at an upper or lower landing, it will charge automatically
  • The power supply should be left plugged in at all times, and the lift may be left on charge indefinitely, as the charger is intuitive and will not overcharge
  • Note: The stairlift must be turned on to enable battery charging. Batteries will not charge when the lift is turned off
• Care and Cleaning
  • The lift should require no technical maintenance to continue to operate at full capability
  • There is no grease or other lubricants used in the drive system, and no adjustments should be required. However, the lift should be inspected annually
  • The lift and rail should be kept clean. Dust can build up on surfaces, and soiling may occur
  • The seat, footrest, chassis, and upholstery can be cleaned with a damp, soapy cloth followed by a clean, damp cloth
  • Do not use abrasive cleaners, as these can damage the finish. If heavy soiling occurs, clean by scrubbing lightly with a soft brush
• Manual Override Operation
  • If your lift fails to operate and the operator does not wish to dismount on the stairway, another person may use the manual override tool to lower (or raise) the lift to a landing. However, please follow the instructions on the bottom safety flap of the lift and turn the lift off. Insert the manual override tool into the hole in the lower safety flap until it engages the motor shaft, and turn in the direction indicated

Troubleshooting of Harmar's Pinnacle SL300 Stair Lift

• If your lift does not operate, diagnose the problem by listening to the beeps emitted
• An intermittent beep for 30 seconds indicates the lift has been stopped off the charge station. This repeats every 5 minutes until the lift is returned to the charge station. It is recommended that the lift is immediately moved to a strip station (located at either end of the rail)
• If the beep codes are not able to be cleared and the lift is not working, please contact your local dealer or Harmar and describe the problem. A local technician will need to be contacted to repair the problem if it cannot be repaired over the phone
• If there is no light on, the charger may have a problem with AC power or the charger itself

Minor faults Harmar Straight Stair Lifts

Single long beep (will reset once the fault is cleared)

• Seat swiveled out of position
• Edge safety detected this is for the folding rail unit only
• Footrest
• Current overload condition
• A Low battery voltage condition

Pulsing Beep of Harmar SL-300 Pinnacle

• The lift stopped off of the charging strip with sound after 30 seconds for 30 seconds.
• It will repeat every 10 minutes until the lift is operated or returned to charge strips.

User Manuals

• SL300 Sell Sheet
• SL300 Brochure
• SL300 Owner’s Manual
• Harmar Pinnacle SL300 Stair Lift Installation Guide