EZ-ACCESS SUITCASE TRIFOLD Advantage Series Ramp

Advantages of EZ-ACCESS TRIFOLD AS Ramp

• TRIFOLD Portable Ramp Design:
  • The unique design of the portable ramp makes it easy to set up and easy to transport from place to place
  • This ramp can separate into two easy-to-carry sections
• Interlocking Hinge:
  • Interlocking hinge are designed for smoother operation and reduced pinch points
• Slip-resistant Portable Ramp:
  • Surface the ramp offers an applied slip-resistant surface
• Self-adjusting Bottom Transition Plate:
  • Features self-adjusting bottom transition plates, which adjusts the ramp to most surfaces, making this ramp one of the safest portable ramps
• Allows for ultimate portability when longer ramp lengths are needed
• Applied, slip-resistant surface
• 800-pound weight capacity
• Optional Top Lip Extension (TLE) allows for rear door access on utility trailers, SUVs, and vans

What to buy with TRIFOLD AS Portable Wheelchair Ramp

• Harmar Vehicle Wiring Harness
• Roll-A-Ramp Seg Mount Brackets
• EZ-ACCESS TRANSITIONS Modular Entry Mat Riser

How to use TRIFOLD SUITCASE Ramp?

Installation Instructions

• Read and follow all instructions before use.
• Do not use it if the ramp is damaged or unstable.
• For wheelchairs and scooters only (not intended for commercial use).
• The ramp is shipped fully assembled. To separate the ramp into two halves for easy stowage and transportation, remove bolts and install hinge pins as follows: Position it. Align hinges, then insert a hinge pin into each hinge assembly and connect ramp sections together before use. The Spring section of the pin should be on the underside (non-treaded side) of the ramp. The ramp may be separated for use when loading or unloading unoccupied mobility equipment only. When used with occupied mobility equipment, use the ramp as one unit (ensure both halves are joined with hinge pins or bolts firmly installed before use).
• Place the ramp on landing in the folded position, making sure that the top lip transition plate (labeled TOP) is resting securely on the landing
• Position the ramp approximately its full length out from the vehicle or step. Facing the vehicle or step, begin working from the left side. Stand the ramp upright on the end with the hinged edge facing to the right. Lift up the first top half of the ramp toward the step or vehicle and place the ramp so that the top lip transition plate is securely supporting the ramp.
• Unfold the second top half of the ramp so that both halves are fully extended lengthwise with one half lying face down on top of the other.
  Note: Applied slip-resistant tread should not be exposed at this time. Open the complete ramp, exposing the entire applied slip-resistant tread surface, then center on landing.
• For ease in carrying and storage, the ramp can be disconnected and carried in two sections. (When hinge pins are not in use, store them on one side of the hinge or on the underside of the ramp by inserting them into the gap behind the top I-beam.)
• To prevent ramp halves from swinging open, ensure that the Dual Lock tab (interlocking fastener) is pressed together and firmly locked in place. Prior to use, locate both of the 1" x 3/4" Dual Lock tabs (found opposite the applied slip-resistant tread side of the ramp, near the top and bottom edges), and then remove the top piece (it's used only as a protective covering).

Safety and Maintenance

• Regularly check the ramp for damage, and check and tighten any loose fasteners
• Keep the ramp surface clear of ice, snow, dirt, leaves, and other debris
• For snow/ice, remove accumulation and sweep the surface clean
• To remove dirt, leaves, and other debris, sweeping the surface or using a garden hose will usually suffice, but, if needed, use a damp cloth or soft brush with non-alkaloid detergent and water
• Rinse well and use extra caution if the ramp surface is wet

User Manuals

• EZ-ACCESS TRIFOLD Ramp Instruction Manual
• SUITCASE TRIFOLD AS Technical Specifications

• SUITCASE Brochure