EZ-ACCESS TRANSITIONS Angled Entry Ramp

EZ-ACCESS TRANSITIONS Angled Entry Ramp Features

Product Highlights:

• Extruded Tread Surface:
  • It is slip-resistant, meaning users are safe to use it in any weather
• Adjustable Legs with Swivel Feet:
  • Allow for two inches of vertical adjustments
  • It adjust independently making the Ramp the perfect solution for uneven surfaces
• Free Standing Portable Entry Ramp Design:
  • It is ideal for entryways with doors that swing both in and out
• High-Strength Aluminum Materials:
  • Made completely out of high-strength aluminum which will not rust or corrode over time
• Height Adjustment:
  • 12": 1-3/8" - 2-3/4"
  • 24": 1-11/16" - 4-3/8"

TRANSITIONS Advantage:

• The sturdy, seam-free surface makes TRANSITIONS ramp a safe solution for wheelchair, scooter, walker, and cane users
• Attractive designs are available in multiple styles and materials to suit user needs and taste
• Slip-resistant tread and surfaces
• Durably designed for years of continued use
• Quick and easy setup and removal - installs in minutes so there's little-to-no disruption
• Ideal for doorways, sliding glass doors, and raised landings
• Portable, convenient, and durable

What to buy with EZ-ACCESS Portable Entry Ramp

• EZ-ACCESS TRANSITIONS Angled Entry Mat
• EZ-ACCESS TRANSITIONS Modular Entry Mat Riser
• EZ-ACCESS Ramp Hanger

How to use TRANSITIONS Angled Entry Ramp?

Getting Started With the Ramp:

1. The aluminum, self-supporting ramp can be used with or without the supplied adjustable swivel feet. To protect floors, foam, rubber, or other non-abrasive, the protective material may be affixed to the underside of the ramp.
2. Measure the rise to determine if the adjustable swivel feet are needed.
3. Position the ramp and adjustable feet as needed to obtain the correct height. Adjust feet as needed to ensure both feet are in contact with the ground.

Fastening Ramp to Landing:
The TRANSITIONS Angled Entry Ramp must be fastened to the landing before use. Use the two pre-drilled holes in the bottom of the ramp to fasten to the landing or threshold. Wood screws, sheet metal screws, or concrete bolts may be necessary, depending on the application.

1. Attaching to Wood:
   Fasten TRANSITIONS Angled Entry Ramp by installing one 1/4" x 1" self-drilling stainless steel screw (supplied) through each hole.
2. Attaching to Concrete:
   - Use the two pre-drilled holes in the bottom of the TRANSITIONS Angled Entry Ramp as a template to mark the positions to drill.
   - Using a 1/4" masonry bit, drill two holes at the marked locations. Drill to a depth specified by the pin drive anchor manufacturer's instructions.
   - After drilling, make sure that the holes are free of any residue and/or debris.
   - Align the TRANSITIONS Angled Entry Ramp over the drilled holes.
   - Install 1/4" x 1 1/2" pin drive concrete anchors into the holes per the pin drive anchor manufacturer instructions.

Safety And Maintenance:

• Regularly check the ramp for damage and tighten any loose fasteners
• Keep the ramp surface clear of ice, snow, dirt, leaves, and other debris
• For snow or ice, remove accumulation and sweep the surface clean
• To remove dirt, leaves, and other debris, sweeping the surface or using a garden hose will usually suffice
• If needed, use a damp cloth or soft brush with non-alkaloid detergent and water
• Rinse well and use extra caution if the ramp surface is wet

Important Information:

• The rated load is 700 pounds, 350 pounds per caster or wheel
• Never exceed the rated load
• Read and follow all labels, instructions, safety and maintenance information before use
• Do not use it if the ramp is damaged or unstable
• For wheelchairs and scooters only (not intended for commercial use)
• The ramp may be slippery when wet or icy
• Use only if sufficient maneuvering room is available at both ends of the ramp to assure safe travel when entering and exiting the ramp
• Use the ramp only with a qualified helper and always use your lap belt

User Guides

• EZ-ACCESS TRANSITIONS Angled Entry Ramp Instruction Manual
• TRANSITIONS Angled Entry Ramp Technical Specifications
• TRANSITIONS Brochure